Roofing Equipment & Boilers Surfacing Plant Tools & Equipment Bitumen Boilers Safety Accessories Spare Parts Accessories & Gas Torches Thermometers LPG, 'Impact' & 'Petal' Industrial Gas burners Thermostat & Boiler Control Jointing & Marking shoes & tools Low Temperature/Polymer/Rubber Materials Agricultural & Marine Cookers

Farvis - Engineering since 1840

“Quality at Trade Prices”

All Farvis Products are design copyrighted

Burner Kits & Packages

Mushroom Burners Heavy Duty Petal burner Burner Kits & Packages

For pre heaters, hot boxes and general industrial use

WE CAN SUPPLY A PACKAGE FOR EXPERIENCED FITTERS TO INSTALL, EITHER ON NEW EQUIPMENT OR AS A REPLACEMENT ON AN EXISTING HEATER.  WE CAN PROVIDE VARIOUS BURNERS AND WHERE NECESSARY A COMPLETE KIT OF PARTS TOGETHER WITH A THERMOSTAT AND BURNER CONTROL SYSTEM.


FLAME FAIL SHUT OFF






THIS WILL SHUT OFF THE SUPPLY OF GAS IN THE EVENT OF THE FLAME GOING OUT, PREVENTING AN UNCONTROLLED ESCAPE OF GAS. IT HAS MANY ADVANTAGES BUT IT IS A RELATIVELY SENSITIVE SYSTEM AND CAN BE SUBJECT TO DAMAGE IF USED IN WET OR AGGRESSIVE CONDITIONS. HENCE IT IS NOT FITTED AS STANDARD TO INDUSTRIAL EQUIPMENT.

THIS PHOTO IS A CLOSE UP OF A FLAME FAILURE SHUT OFF AND AUXILIARY CONTROL TAP FITTED TO A BAR BURNER. THIS MODIFICATION CAN BE FITTED TO ANY OF OUR BURNERS ALTHOUGH A PILOT LIGHT MAY BE NEEDED IN SOME CASES.

THIS MODIFICATION MUST BE SPECIFIED AT THE TIME OF ORDER.

Available on standard mushroom burner, heavy duty pot burner and bar burners.

HOSE & REGULATOR SET


THE SAFE WAY TO OPERATE YOUR EQUIPMENT - BITUMEN BOILERS MUST USE ARMOURED HOSE.









4 METRE HEAVY DUTY ARMOURED GAS HOSE TO BRITISH STANDARD AND HIGH FLOW ADJUSTABLE REGULATOR, PRE ASSEMBLED AND READY TO OPERATE.  HOSE END FITTINGS SCREW DIRECTLY TO OUR EQUIPMENT WITHOUT THE NEED FOR HOSE ADAPTERS OR PIPE CLIPS.  MADE TO OUR SPECIFICATION BY A MAJOR SUPPLIER OF QUALITY BRITISH GAS EQUIPMENT THIS UNIT IS LONG LASTING, ROBUST AND RELIABLE.

HOSE LENGTHS

SEPARATE LENGTHS OF ARMOURED GAS HOSE AND FITTINGS ARE AVAILABLE WITH PRE MADE 1/4" MALE AND NUT/CONE  FITTINGS TO FIT TO A STANDARD 1/4" REGULATOR FEMALE OUTPUT AND FARVIS BUILT EQUIPMENT. STANDARD LENGTH IS  15 FEET ( 5 m ).








FITTINGS:  1/4" BSPT MALE AT REGULATOR END - 1/4" CONE & 1/4" CAPTIVE NUT AT APPLIANCE END

NOT ILLUSTRATED:  BARE LENGTHS OF SINGLE MESH STEEL BRAIDED ARMOURED HOSE AVAILABLE "FROM THE REEL" IN LENGTHS UP TO 120 FEET TO SUIT CUSTOMER REQUIREMENTS.   FITTINGS AND HOSE CONNECTORS FROM STOCK.

Note: it is extremely dangerous to operate gas equipment in a position where you can't reach the gas cylinder or with an excessive length of hose.

DO NOT OPERATE WITH THE APPLIANCE ON A ROOF AND THE CYLINDER AT GROUND LEVEL

MULTI-CYLINDER CONNECTIONS


IF YOU NEED A LARGE OFF-TAKE OF GAS OR YOUR CYLINDERS BEGIN TO 'FREEZE BACK' AND GAS OUTPUT DROPS ALTHOUGH THERE IS STILL PLENTY OF GAS IN THE CYLINDER, USUALLY WITH 'SNOW' FORMING ON THE OUTSIDE OF THE CYLINDER, THIS WILL USUALLY PROVIDE THE ANSWER -

CONNECT TWO OR MORE CYLINDERS TO ONE APPLIANCE

OR TWO APPLIANCES TO ONE GAS CYLINDER!

We manufacture special burners for film effects -  including ‘heat haze’ , ‘fuel fire’ and ‘directed flame’ for dragons , monsters etc ! Manual and remote control systems available.

FILM & SPECIAL EFFECT BURNERS